Skip to content

Get 25% OFF your first month on every game! 🎉

In Australia? Our Australian site has the same servers, priced in Australian dollars.
In Australia? Our Australian site has the same servers, priced in Australian dollars.
In New Zealand? Our site for Australia and New Zealand has the same servers.
In New Zealand? Our site for Australia and New Zealand has the same servers.

BeamMPSettings and admin

How to change the map on a BeamMP server

Switch your BeamMP server to any stock BeamNG.drive map, or add a modded map zip and find the folder name its Map path needs.

Updated 3 min read

To change the map on a BeamMP server, set Map in Server Options > Startup Parameters, press Save and restart the server. A BeamMP server runs one map at a time, set as a path that ends in /info.json. The maps that come with BeamNG.drive need only that path. A modded map needs its zip on the server too.

Checked against BeamMP-Server v3.9.3, November 2026.

Change to a stock map

  1. Open your server and go to Server Options > Startup Parameters.
  2. Type the map's path into Map, exactly as it appears in the list below.
  3. Press Save on that row.
  4. Restart the server.

New servers start on /levels/gridmap_v2/info.json. These are the paths of the stock maps in current BeamNG.drive:

  • /levels/gridmap_v2/info.json
  • /levels/automation_test_track/info.json
  • /levels/east_coast_usa/info.json
  • /levels/hirochi_raceway/info.json
  • /levels/italy/info.json
  • /levels/jungle_rock_island/info.json
  • /levels/industrial/info.json
  • /levels/small_island/info.json
  • /levels/smallgrid/info.json
  • /levels/utah/info.json
  • /levels/west_coast_usa/info.json
  • /levels/driver_training/info.json
  • /levels/derby/info.json
  • /levels/johnson_valley/info.json

Stock maps are already in every player's game, so nobody downloads anything for them.

Warning

Set the map on the Startup Parameters page, not in ServerConfig.toml. The panel writes Map into that file every time the server starts, so a change made in the file is lost.

Add a modded map

A modded map is a .zip file. Keep it zipped from start to finish.

  1. Open the File Manager tab and open the Resources folder, then Client.
  2. Press Upload and pick the map's .zip. The browser takes files up to 100 MB. For a bigger map, connect over SFTP and put it in the same folder.
  3. On your PC, open the zip without extracting it, and open the levels folder inside. It holds one folder, named after the map. Note that name exactly, with the same capitals and underscores.
  4. Go to Server Options > Startup Parameters and set Map to /levels/<folder name>/info.json. For a folder called my_drift_map, that's /levels/my_drift_map/info.json.
  5. Press Save and restart the server.

When players join, BeamMP sends them the map with the rest of your mods. Install mods on a BeamMP server has more on how that works.

If the map doesn't load

A wrong folder name is a common cause. Check the path again against the folder inside the zip, and make sure it still ends in /info.json.

If it still doesn't load, let the game tell you the right name:

  1. Install the map in your own copy of BeamNG.drive and load into it in single player.
  2. Open the game's console with the ~ key. On a keyboard without that key, find Toggle System Console under Options > Controls > Bindings, in the General Debug section.
  3. Run print(getMissionFilename()). It prints the name the server needs.

Keep the Client folder tidy

Every zip in Resources/Client goes to each player who joins, whether the server runs that map or not. When you stop using a map, delete its zip in the File Manager so joins stay quick. A backup first means you can bring it back later.

More BeamMP guides

Ready to launch your BeamMP server?

Your choice of location, NVMe disks and DDoS protection, with the version and mod loader yours to change whenever you like.

See BeamMP plans